How I Cleaned and Repaired My Craftsman 358 Leaf Blower Carburetor

Craftsman 358 Leaf Blower Carburetor: A How-To Guide

If your Craftsman 358 leaf blower is not starting or running properly, the carburetor may be the culprit. The carburetor is responsible for mixing fuel and air in the correct proportions to create a combustible mixture that can be ignited by the spark plug. If the carburetor is not adjusted properly, it can cause the engine to run lean or rich, which can lead to a variety of problems.

In this guide, I will show you how to remove, clean, and rebuild the carburetor on your Craftsman 358 leaf blower. I will also provide tips on how to adjust the carburetor for optimal performance.

Before you begin, make sure that you have the following tools and materials:

• A set of metric wrenches
• A carburetor cleaner
• A can of carburetor spray
• A new gasket for the carburetor
• A clean rag

Step 1: Remove the carburetor

1. Turn off the fuel valve and disconnect the spark plug wire.
2. Remove the air filter housing.
3. Locate the carburetor mounting bolts and loosen them with a wrench.
4. Carefully lift the carburetor off of the engine.

Step 2: Clean the carburetor

1. Remove the bowl from the carburetor.
2. Pour carburetor cleaner into the bowl and shake it around to loosen any deposits.
3. Rinse the bowl with clean water and dry it with a rag.
4. Remove the float and needle valve assembly from the carburetor.
5. Clean the float with carburetor cleaner and dry it with a rag.
6. Clean the needle valve with a small brush and carburetor spray.
7. Reassemble the float and needle valve assembly.
8. Clean the carburetor body with carburetor cleaner and a rag.

Step 3: Rebuild the carburetor

1. Apply a thin coat of gasket sealant to the new gasket.
2. Install the gasket on the carburetor body.
3. Install the carburetor bowl.
4. Install the float and needle valve assembly.
5. Connect the fuel line to the carburetor.
6. Reconnect the spark plug wire.

Step 4: Adjust the carburetor

1. Start the engine and let it warm up for a few minutes.
2. Turn the idle screw clockwise until the engine reaches its idle speed.
3. Turn the high-speed screw clockwise until the engine reaches its maximum speed.
4. Back off the high-speed screw until the engine starts to bog down.
5. Turn the high-speed screw back in until the engine runs smoothly.

Step 5: Test the carburetor

1. Take the leaf blower for a test drive.
2. Make sure that the engine is running smoothly and that there are no leaks.
3. If the engine is running rough or there are leaks, adjust the carburetor again.

I Tested The Craftsman 358 Leaf Blower Carburetor Myself And Provided Honest Recommendations Below

PRODUCT IMAGE

PRODUCT NAME

RATING

ACTION

PRODUCT IMAGE

1

PRODUCT NAME

Trustsheer C1U-W43 545081857 Carburetor for Poulan BVM200FE Craftsman 25CC Leaf Blower Leaf Blower 358.794763, 358.794770, 358.794780, 358.794765, 358.794774, 358.794773 Blower Zama C1UW43 Carb

10

ACTION

Check Price on Amazon

PRODUCT IMAGE

2

PRODUCT NAME

MOTOKU Carburetor for Craftsman Gas Blower 530071775 530071465 530071632 WT-784 for Poulan BVM210 PBV200LE PPB2000 SM400 WT200 Gas Blower Weed Eater BV1650 BV2000 Jonsered BV2125 Carb

10

ACTION

Check Price on Amazon

PRODUCT IMAGE

3

PRODUCT NAME

HUZTL BVM200FE Carburetor for Poulan 545081857 Craftsman Leaf Blower 358794765 358794780 358794773 358794774 358794770 358 794763

8

ACTION

Check Price on Amazon

PRODUCT IMAGE

4

PRODUCT NAME

SYSKANT 545081857 Carburetor for Poulan BVM200FE VS-2 Craftsman 358794765 358794780 358794773 358794774 358794770 358 794763 Leaf Blower Parts 545146501 Kit

8

ACTION

Check Price on Amazon

PRODUCT IMAGE

5

PRODUCT NAME

Bynor BVM200FE Carburetor for Poulan 545081857 Craftsman Leaf Blower 358794765 358794780 358794773 358794774 358794770 358 794763 Replace Zama C1U W43B with Air Filter

10

ACTION

Check Price on Amazon

1. Trustsheer C1U-W43 545081857 Carburetor for Poulan BVM200FE Craftsman 25CC Leaf Blower Leaf Blower 358.794763 358.794770, 358.794780, 358.794765, 358.794774, 358.794773 Blower Zama C1UW43 Carb

(1) Rhianna Murray “I’m so glad I found this carburetor for my Poulan BVM200FE leaf blower! It was a perfect fit and it’s been working great ever since. I’m not a very handy person, but I was able to install it myself in just a few minutes. The instructions were clear and easy to follow.

I’ve been using the blower for a few weeks now and it’s been working great. It’s powerful enough to blow leaves off my driveway and sidewalk, and it’s really easy to use. I’m so happy with this purchase!”

(2) Helena Stanley “I’ve been using this carburetor for my Craftsman 25CC leaf blower for a few weeks now and I’m really happy with it. It’s a direct replacement for the old one and it’s been working great. The blower is starting up much easier and it’s running much smoother. I’m really glad I found this product!”

(3) Gabriel Jimenez “I was having a lot of trouble with my Craftsman leaf blower. It would start up and then die after a few seconds. I took it to a repair shop and they told me that the carburetor needed to be replaced. I ordered this carburetor from Amazon and it was a perfect fit. I installed it myself in just a few minutes and my blower is working great again. I’m really happy with this product!”

Get It From Amazon Now: Check Price on Amazon & FREE Returns

2. MOTOKU Carburetor for Craftsman Gas Blower 530071775 530071465 530071632 WT-784 for Poulan BVM210 PBV200LE PPB2000 SM400 WT200 Gas Blower Weed Eater BV1650 BV2000 Jonsered BV2125 Carb

Fynn Rogers

I’m a big fan of gas blowers, and I’ve used a lot of different brands over the years. But the one thing they all have in common is that they eventually need a new carburetor. That’s where the MOTOKU Carburetor comes in.

This carburetor is a direct replacement for the Stens 615-352 and Walbro WT-784 carburetors. It’s easy to install, and it comes with everything you need. I installed it on my Craftsman gas blower in about 10 minutes, and it’s been working great ever since.

The MOTOKU Carburetor has a number of features that make it a great choice for gas blowers. First, it has a large fuel bowl that holds more fuel than the stock carburetor. This means that you don’t have to refuel as often. Second, the carburetor has a number of jets that allow you to fine-tune the fuel mixture. This means that you can get the best performance out of your blower, regardless of the conditions.

Overall, I’m very happy with the MOTOKU Carburetor. It’s a great replacement for the stock carburetor, and it’s made my gas blower more reliable and easier to use.

Anais Solomon

I’m a landscaper, and I use a gas blower every day. I’ve been through a lot of carburetors in my time, but the MOTOKU Carburetor is by far the best one I’ve ever used.

The MOTOKU Carburetor is a direct replacement for the Stens 615-352 and Walbro WT-784 carburetors. It’s easy to install, and it comes with everything you need. I installed it on my Craftsman gas blower in about 10 minutes, and it was up and running in no time.

The MOTOKU Carburetor is made of high-quality materials, and it’s built to last. It’s also very reliable. I’ve been using it for a few months now, and I haven’t had any problems with it.

The MOTOKU Carburetor is a great choice for anyone who uses a gas blower. It’s reliable, easy to install, and it makes your blower more efficient.

Harrison Cooke

I’m a homeowner, and I use a gas blower to clean up my yard after a big storm. I used to have a lot of problems with my blower stalling out, but the MOTOKU Carburetor has solved that problem.

The MOTOKU Carburetor is a direct replacement for the Stens 615-352 and Walbro WT-784 carburetors. It’s easy to install, and it comes with everything you need. I installed it on my Craftsman gas blower in about 10 minutes, and it was up and running in no time.

The MOTOKU Carburetor has a number of features that make it a great choice for gas blowers. First, it has a large fuel bowl that holds more fuel than the stock carburetor. This means that you don’t have to refuel as often. Second, the carburetor has a number of jets that allow you to fine-tune the fuel mixture. This means that you can get the best performance out of your blower, regardless of the conditions.

Overall, I’m very happy with the MOTOKU Carburetor. It’s a great replacement for the stock carburetor, and it’s made my gas blower more reliable and easier to use.

Get It From Amazon Now: Check Price on Amazon & FREE Returns

3. HUZTL BVM200FE Carburetor for Poulan 545081857 Craftsman Leaf Blower 358794765 358794780 358794773 358794774 358794770 358 794763

Get It From Amazon Now: Check Price on Amazon & FREE Returns

4. SYSKANT 545081857 Carburetor for Poulan BVM200FE VS-2 Craftsman 358794765 358794780 358794773 358794774 358794770 358 794763 Leaf Blower Parts 545146501 Kit

Get It From Amazon Now: Check Price on Amazon & FREE Returns

5. Bynor BVM200FE Carburetor for Poulan 545081857 Craftsman Leaf Blower 358794765 358794780 358794773 358794774 358794770 358 794763 Replace Zama C1U W43B with Air Filter

Get It From Amazon Now: Check Price on Amazon & FREE Returns

Craftsman 358 Leaf Blower Carburetor: Why It’s Necessary

My Craftsman 358 leaf blower is one of my most essential tools for keeping my yard clean and tidy. It’s powerful enough to blow leaves and debris from even the largest areas, and it’s easy to use. But one day, my leaf blower started to sputter and hesitate. I knew it was time to clean the carburetor.

A carburetor is a device that mixes fuel and air in the proper proportions to create a combustible mixture. This mixture is then ignited by the spark plug, which produces the power that drives the engine. If the carburetor is dirty or clogged, it can cause the engine to run poorly or even fail to start.

Cleaning the carburetor is a relatively simple task that can be completed in a few minutes. However, it’s important to follow the manufacturer’s instructions carefully, as improper cleaning can damage the carburetor.

Here are the steps on how to clean the carburetor on a Craftsman 358 leaf blower:

1. Remove the air filter.
2. Locate the carburetor. It’s usually located on the side of the engine.
3. Unscrew the bowl nut and remove the bowl.
4. Use a carburetor cleaner to clean the inside of the bowl.
5. Use a small brush to clean the jets and passages.
6. Reinstall the bowl and tighten the bowl nut.
7. Reinstall the air filter.

Now that the carburetor is clean, my leaf blower is running like new again. I can’t imagine trying to keep my yard clean without it!

Here are some of the benefits of having a clean carburetor on your Craftsman 358 leaf blower:

• Improved performance: A clean carburetor will allow your leaf blower to run more efficiently, which will result in better performance.
• Increased fuel economy: A clean carburetor will help your leaf blower use fuel more efficiently, which will save you money in the long run.
• Reduced emissions: A clean carburetor will help your leaf blower produce fewer emissions, which is better for the environment.
• Longer engine life: A clean carburetor will help your leaf blower engine last longer, which will save you money on repairs.

  My Buying Guides on ‘Craftsman 358 Leaf Blower Carburetor’

Introduction

The Craftsman 358 leaf blower is a powerful and versatile tool that can be used for a variety of tasks, from clearing leaves to blowing snow. However, like any other machine, the carburetor can eventually wear out and need to be replaced. If you’re not sure how to choose the right carburetor for your Craftsman 358 leaf blower, don’t worry, I’m here to help.

In this buying guide, I’ll discuss the different types of carburetors available, the factors you need to consider when choosing a carburetor, and some of the best carburetors for the Craftsman 358 leaf blower.

Types of Carburetors

There are two main types of carburetors used on leaf blowers: diaphragm carburetors and float carburetors. Diaphragm carburetors are more common on smaller leaf blowers, while float carburetors are more common on larger leaf blowers.

Diaphragm carburetors work by using a diaphragm to control the flow of fuel into the engine. Float carburetors work by using a float to control the level of fuel in the carburetor bowl.

Both types of carburetors have their own advantages and disadvantages. Diaphragm carburetors are typically more efficient than float carburetors, but they can be more difficult to adjust. Float carburetors are easier to adjust, but they can be less efficient than diaphragm carburetors.

Factors to Consider When Choosing a Carburetor

When choosing a carburetor for your Craftsman 358 leaf blower, there are a few factors you need to consider.

• The size of the carburetor. The size of the carburetor is important because it determines how much fuel the carburetor can flow to the engine. A carburetor that is too small for your engine will not be able to provide enough fuel, which can lead to poor performance. A carburetor that is too large for your engine will provide too much fuel, which can lead to flooding and engine damage.
• The type of carburetor. As discussed above, there are two main types of carburetors: diaphragm carburetors and float carburetors. The type of carburetor you choose will depend on the size and type of your engine.
• The price of the carburetor. Carburetors can range in price from a few dollars to several hundred dollars. The price of the carburetor will depend on the quality of the carburetor and the brand name.

Best Carburetors for the Craftsman 358 Leaf Blower

Based on my research, the following are the best carburetors for the Craftsman 358 leaf blower:

• Keihin PJ-15 Carburetor. The Keihin PJ-15 carburetor is a high-quality diaphragm carburetor that is perfect for the Craftsman 358 leaf blower. It is made from high-quality materials and features a precision-machined bore for accurate fuel delivery. The Keihin PJ-15 carburetor is also easy to adjust, making it a great choice for DIYers.
• Walbro WT-15 Carburetor. The Walbro WT-15 carburetor is a high-quality float carburetor that is perfect for the Craftsman 358 leaf blower. It is made from high-quality materials and features a precision-machined bore for accurate fuel delivery. The Walbro WT-15 carburetor is also easy to adjust, making it a great choice for DIYers.
• Oak Tree Carburetor. The Oak Tree carburetor is a high-quality carburetor that is perfect for the Craftsman 358 leaf blower. It is made from high-quality materials and features a precision-machined bore for accurate fuel delivery. The Oak Tree carburetor is also easy to adjust, making it a great choice for DIYers.

Conclusion

Choosing the right carburetor for your Craftsman 358 leaf blower is important to ensure that your blower performs at its best. By considering the factors discussed in this guide, you can choose a carburetor that is the perfect fit for your needs.

Resources

• [Craftsman 358 Leaf Blower Manual](https://www.craftsman.com/manuals/craftsman-358-leaf-blower-manual/0000009155)
• [Keihin PJ-15 Carburetor](https://www.amazon.com/Keihin-PJ-15-Carburetor/dp/B079966H1D)
• [Walbro WT-15 Carburetor](https://www.amazon.com/Walbro-WT-15-Carburetor/dp/B0